NiQor High Voltage DC-DC Converters
    High input voltage, non-isolated brick DC-DC converters
NiQor Series Hi-Voltage Non-Isolated DC-DC Converters The high input voltage NiQor® family of DC-DC converters offer a unique solution for converting high-powered, varible voltages to a wide range of output voltages. The converter is a non-isolated buck-boost regulator, which employs synchronous rectification to achieve extremely high conversion efficiency. Suitable for use in IBA or to provide a regulated output voltage from a battery source or other variable voltage source. Can be configured to Buck the input voltage down or Boost the input voltage up using a single external resistor.
Product Links
Product Part Numbering Convention
 
Eighth-Brick
                              jump to    Eighth-Brick      Quarter-Brick     Half-Brick Standard     Half-Brick Flanged 
 
InQor Encased Mechanical Drawing
 
   NOTES
  1. Pins 1-3, 5-7 are 0.040" (1.02 mm) diameter. with 0.080" (2.03mm) diameter standoff shoulders.
  2. Pins 4 and 8 are 0.062" (1.57 mm) diameter with 0.100" (2.54 mm) diameter standoff shoulders.
  3. Other pin extension lengths available. Recommended pin length is 0.03" (0.76 mm) greater than the PCB thickness.
  4. All Pins: Material - Copper Alloy Finish - Matte Tin over Nickel plate
  5. Undimensioned components are shown for visual reference only.
  6. All dimensions in inches (mm) Tolerances: x.xx 0.02" (x.x 0.5 mm) x.xxx 0.010" (x.xx 0.25 mm)
  7. Weight: 1.7 oz (48 g) typical
  8. Workmanship: Meets or exceeds IPC-A-610C Class II
   PIN-OUT         See NiQor Converters Pin-Out description
Quarter-Brick
                              jump to    Eighth-Brick      Quarter-Brick     Half-Brick Standard     Half-Brick Flanged 
 
InQor Encased Mechanical Drawing
 
   NOTES
  1. M3 screws used to bolt unit's baseplate to other surfaces such as heatsinks must not exceed 0.090" (2.28mm) depth below the surface of the baseplate.
  2. Applied torque per screw should not exceed 6in-lb (0.7nm)
  3. Baseplate flatness tolerance is 0.004" (.10mm) TIR for surface
  4. Pins 1-3, 5-7 are 0.040" (1.02mm) dia. with 0.080" (2.03mm) dia. standoff shoulders
  5. Pins 4 and 8 are 0.062" (1.57mm) dia. with 0.100" (2.54mm) dia. standoff shoulders
  6. All pins: material: copper alloy finish: matte tin over nickel plate
  7. Undimensioned components are shown for visual reference only
  8. All dimensions in inches(mm) tolerances:
          x.xxin ±0.02 (x.xmm +/-0.5mm)
          x.xxxin ±0.010 (x.xxmm +/-0.25mm)
  9. Weight: =3oz (85g) typical
  10. Workmanship: meets or exceeds IPC-A-610C Class II
   PIN-OUT         See NiQor Converters Pin-Out description
Half-Brick (standard)
                              jump to    Eighth-Brick      Quarter-Brick     Half-Brick Standard     Half-Brick Flanged 
 
InQor Encased Mechanical Drawing
 
   NOTES
  1. Applied torque per screw should not exceed 6in-lb (.7Nm)
  2. Baseplate flatness tolerance is 0.004" (.10mm) TIR for surface
  3. Pins 1-3, 5-7, A and C are 0.040" (1.02 mm) dia. with 0.080" (2.03mm) dia. standoff shoulders.
  4. Pins 4 and 8 are 0.080" (2.03 mm) dia. with 0.125" (3.18 mm) dia. standoff shoulders.
  5. All Pins: Material - Copper Alloy Finish - Matte Tin over Nickel plate
  6. Undimensioned components are shown for visual reference only.
  7. All dimensions in inches (mm) Tolerances: x.xx 0.02" (x.x 0.5 mm) x.xxx 0.010" (x.xx 0.25 mm)
  8. Weight: TBD
  9. Threaded or non-threaded options available
  10. Workmanship: Meets or exceeds IPC-A-610C Class II
   PIN-OUT         See NiQor Converters Pin-Out description
Half-Brick (flanged)
                              jump to    Eighth-Brick      Quarter-Brick     Half-Brick Standard     Half-Brick Flanged 
 
InQor Encased Mechanical Drawing
 
   NOTES
  1. Applied torque per screw should not exceed 5in-lb, 3 in-lb recommended 
  2. Baseplate flatness tolerance is 0.01" (.10mm) TIR for surface
  3. Pins 1-3, 5-7, A and C are 0.040" (1.02 mm) dia. with 0.080" (2.03mm) dia. standoff shoulders.
  4. Pins 4 and 8 are 0.080" (2.03 mm) dia. with 0.125" (3.18 mm) dia. standoff shoulders.
  5. All Pins: Material - Copper Alloy Finish - Matte Tin over Nickel plate
  6. Undimensioned components are shown for visual reference only.
  7. All dimensions in inches (mm) Tolerances: x.xx 0.02" (x.x 0.5 mm) x.xxx 0.010" (x.xx 0.25 mm)
  8. Weight: TBD
  9. Threaded or non-threaded options available
  10. Workmanship: Meets or exceeds IPC-A-610C Class II
   PIN-OUT         See NiQor Converters Pin-Out description